Abre APP!

Disfruta de ofertas exclusivas de APP.

Abre APP
Extrusora de Impresora 3D de Larga Distancia de 0,4 mm
Extrusora de Impresora 3D de Larga Distancia de 0,4 mm
Extrusora de Impresora 3D de Larga Distancia de 0,4 mm
Extrusora de Impresora 3D de Larga Distancia de 0,4 mm
1/1

Extrusora de Impresora 3D de Larga Distancia de 0,4 mm - Plata 0.3MM

Ver Traducción
MXN$254.53
12.92
104 Opiniones

Cupón:

promoción:

Apoyo COD Pago

Warehouse & Fee

Select
HK-4:Fecha de despacho: Apr 22 - Apr 24

Product Options

Select
Plata 0.3MM
Visita la tienda

Comentarios (104)

Eleny
Aug 24,2018
Some time ago I bought an Anet A6 printer on this page, I made several modifications and this article had wanted it for a long time, actually I have seen so many good results that managed to make it acquire it, I like the speed that prints with estre extruder E3D V6, also gives an elegant appearance and manages to make good finishes, no doubt would always recommend.
Ver Más

Descripción

E3D - V6 3D extrusora de impresora Hot End Kit completo

Principales Características:
● Traje para material de 1.75mm
● El E3D-V6 es la versión actualizada del E3D-V5
● El E3D - V6 ha reducido la longitud, el grosor y el diámetro del radiador (las longitudes más cortas ayudan a aumentar la estabilidad del extremo caliente)
● Bloque de calefacción es más simple y práctico
● Aumento del número de disipadores de calor, mejor rendimiento de la disipación de calor
● El tubo de teflón reduce la fricción entre el filamento y la tubería de radiación

Especificación

General

Modelo: E3D - V6
Conveniente para: Refrigeración/ calefacción,Boquilla
Tipo: Piezas de la Extrusora

Peso y Tamaño

Tamaño de Paquete: 16,00 x 15,00 x 6,00 cm / 6,3 x 5,91 x 2,36 pulgadas
Peso de Paquete: 0,1200 kg
Peso de Producto: 0,0960 kg

Contenido de Paquete

Contenido del Paquete: 1 x E3D - V6 Extrusora de Impresora 3D de Larga Distancia (Línea de 1m), 1 x Tubo PTFE (Línea de 1m)

Extrusora de Impresora 3D de Larga Distancia de 0,4 mm- 4GB RAM + 64GB SSD UK plug 0.3MM

Extrusora de Impresora 3D de Larga Distancia de 0,4 mm- 4GB RAM + 64GB SSD UK plug 0.3MM


Responsabilidad de Seguridad de los Productos :
No aceptamos ninguna responsabilidad u obligación por el uso incorrecto de este o cualquier otro producto. Todos nuestros productos son ampliamente probados para cumplir con normas rigurosas y estrictas de control de calidad. Para determinados productos (por ejemplo, juguetes, cuchillos, etc) se recomienda una supervisión adecuada, ya que no nos hacemos responsables de accidentes o usos indebidos.

Productos Recomendados

Productos Patrocinados

Bono de Nuevo Miembro: cupón de $50
MXN$254.53

Extrusora de Impresora 3D de Larga Distancia de 0,4 mm

Color

Tamaño

Cantidad - +
plazos: elija
loading...
loading...
cancelar
loading...
loading...
loading...

Comentarios

4.82 *****
  • 89
  • 15
  • 0
  • 0
  • 1
  • Todo ( 104 )
  • ( 47 )
  • ( 9 )
Eleny
Aug 24,2018
Some time ago I bought an Anet A6 printer on this page, I made several modifications and this article had wanted it for a long time, actually I have seen so many good results that managed to make it acquire it, I like the speed that prints with estre extruder E3D V6, also gives an elegant appearance and manages to make good finishes, no doubt would always recommend.
Luis Alvarez
Jan 15,2019
this is a e3d v6 copy, look very similar but have something differences, is very hard to install, only for advances users, config is very very extend, try and failure, but once installed, prints are beautiful, quality 100%
Ronan Tully
Jun 13,2018
Good print head, works great when you get it set up properly. Make sure you tighten it well when it is hot. Retraction settings need to be much lower then with a direct print head or it will constantly clog. Throat is lined so I would recommend if you are printing hotter plastics to swap it for an all metal one. Installed on my A8 with no problems.
Sugerencia:
Lack of instructions, but go to the E3D site to install correctly.
Extruder Nozzle
Dec 12,2017
This is actually my 2nd pair. As you may know, overtime the nozzle will clog up and im to lazy to clean it up. just replace it. The quality is good. you basically just screw it in the heated block of the printer. Done!
Sugerencia:
No issues.
Gelbrook
Dec 20,2018
I planed for weeks to mount this hotend on my Anet A8, when I finally achieve it I saw that the thermal sensor is not working.The temperature displayed on the main screen is always 0° and my printer run into error when I tried to preheat the hotend : E1 heating failed, PRINTED HALTED, please resetI tried to re-plug my old hothead and it works fine.This hotend is definitely not working, I'm very disapointed
Johan
May 26,2018
This all metal hotend works really good, put it on my Creality Ender-2, could reduce retraction from 7mm to 2.5mm, the whole hotend and PTFE tube have a smaller inner diameter than stock. I haven't tested the heater element nor the thermistor yet (I used the original ones)
Sugerencia:
There were some ridges in the throat that I easily removed by hand with a 2mm drill bit. due to the big cooling block it sits a bit futher out from the bracket so I lost a little printable space in the Y.
JanTchi
Jan 01,2019
Very nice extruder. Extremely high precision. Max speed with this one is about 150mm/s in bowden configuration and I use it for about 260°C for PETG. I make a Zeus cage for this one.
Thorsten
Mar 16,2017
-All metall - no PTFE-tubing inside -Threads are butter-smooth -Very light The throat is M7 on the cold-end side and M6 on the hot-end side, the heater-block clamps down on the heater-element, just like the original from E3D.
Sugerencia:
Since the inner diameter of the Throat was slightly smaller than of the bowden-tube the filament got stuck right on the "seam" between the tube and the throat. I had to work a little on the first 5mm or so of the throat with a 2mm ball-tip-tool from my gravure-set, to make it a little bit wider. Now it works good.
OtterNas3
Mar 18,2017
I will replace the Extruder on my Anet A8 with this, it looks good, the Packaging was "ok" If this piece will work great, i will definately buy another three of these for the other Printer's! Thanks GB for the Service!
Sugerencia:
Nothing bad to sa on this one :)
Overlrod_Laharl
Jan 12,2018
-All metal -works very well -Bowden (this means the extruder motor gets mounted on the printer frame, and this means less mass (thus jerk) on the extruder carriage) -includes almost everythign needed for use
Sugerencia:
-due to variances of different printers a method to mount this is not included. you will need to print one. so this requires a working printer -due to the limitations of the bowden design there is more stringing. -you will need to add custom firmware on your printer to use this.
Ver Más
Ver Más
Ver Más